10.5: Semiconductors Band Gaps, Colors, Conductivity and Doping
 Page ID
 183356
Semiconductors, as we noted above, are somewhat arbitrarily defined as insulators with band gap energy < 3.0 eV (~290 kJ/mol). This cutoff is chosen because, as we will see, the conductivity of undoped semiconductors drops off exponentially with the band gap energy and at 3.0 eV it is very low. Also, materials with wider band gaps (e.g. SrTiO_{3}, E_{gap} = 3.2 eV) do not absorb light in the visible part of the spectrum
There are a number of places where we find semiconductors in the periodic table:
 Early transition metal oxides and nitrides, especially those with d^{0} electron counts such as TiO_{2}, TaON, and WO_{3}
 Oxides of later 3d elements such as Fe_{2}O_{3}, NiO, and Cu_{2}O
 Layered transition metal chalcogenides with d^{0}, d^{2} and d^{6} electron counts including TiS_{2}, ZrS_{2}, MoS_{2}, WSe_{2}, and PtS_{2}
 d^{10} copper and sliver halides, e.g., CuI, AgBr, and AgI
 Zincblende and wurtzitestructure compounds of the pblock elements, especially those that are isoelectronic with Si or Ge, such as GaAs and CdTe. While these are most common, there are other pblock semiconductors that are not isoelectronic and have different structures, including GaS, PbS, and Se.
A 2" wafer cut from a GaAs single crystal. GaAs, like many pblock semiconductors, has the zincblende structure. 
The pblock octet semiconductors are by far the most studied and important for technological applications, and are the ones that we will discuss in detail.
Zincblende and wurtzitestructure semiconductors have 8 valence electrons per 2 atoms. These combinations include 44 (Si, Ge, SiC,…), 35 (GaAs, AlSb, InP,…), 26 (CdSe, HgTe, ZnO,…), and 17 (AgCl, CuBr,…) semiconductors. Other variations that add up to an octet configuration are also possible, such as Cu^{I}In^{III}Se_{2}, which has the chalcopyrite structure, shown at the right.
The chalcopyrite structure is adopted by ABX_{2} octet semiconductors such as Cu^{I}In^{III}Se_{2} and Cd^{II}Sn^{IV}P_{2}. The unit cell is doubled relative to the parent zincblende structure because of the ordered arrangement of cations. Each anion (yellow) is coordinated by two cations of each type (blue and red). 
How does the band gap energy vary with composition? There are two important trends
(1) Going down a group in the periodic table, the gap decreases:


 C (diamond) > Si > Ge > αSn

E_{gap} (eV): 5.4 1.1 0.7 0.0
This trend can be understood by recalling that E_{gap} is related to the energy splitting between bonding and antibonding orbitals. This difference decreases (and bonds become weaker) as the principal quantum number increases.
(2) For isoelectronic compounds, increasing ionicity results in a larger band gap.


 Ge < GaAs < ZnSe
 0.7 1.4 2.8 eV



 Sn < InSb < CdTe < AgI
 0.0 0.2 1.6 2.8 eV

This trend can also be understood from a simple MO picture, as we discussed in Ch. 2. As the electronegativity difference Δχ increases, so does the energy difference between bonding and antibonding orbitals.
The band gap is a very important property of a semiconductor because it determines its color and conductivity. Many of the applications of semiconductors are related to band gaps:
 Narrow gap materials (Hg_{x}Cd_{1}_{}_{x}Te, VO_{2}, InSb, Bi_{2}Te_{3}) are used as infrared photodetectors and thermoelectrics (which convert heat to electricity).
 Wider gap materials (Si, GaAs, GaP, GaN, CdTe, CuIn_{x}Ga_{1x}Se_{2}) are used in electronics, lightemitting diodes, and solar cells.
Color wheel showing the colors and wavelengths of emitted light. 
Semiconductor solid solutions such as GaAs_{1x}P_{x} have band gaps that are intermediate between the end member compounds, in this case GaAs and GaP (both zincblende structure). Often, there is a linear relation between composition and band gap, which is referred to as Vegard's Law. This "law" is often violated in real materials, but nevertheless offers useful guidance for designing materials with specific band gaps. For example, red and orange lightemitting diodes (LED's) are made from solid solutions with compositions of GaP_{0.40}As_{0.60} and GaP_{0.65}As_{0.35}, respectively. Increasing the mole fraction of the lighter element (P) results in a larger band gap, and thus a higher energy of emitted photons.
Colors of semiconductors
The color of absorbed and emitted light both depend on the band gap of the semiconductor. Visible light covers the range of approximately 390700 nm, or 1.83.1 eV. The color of emitted light from an LED or semiconductor laser corresponds to the band gap energy and can be read off the color wheel shown at the right.
Fe_{2}O_{3} powder is reddish orange because of its 2.2 eV band gap 
The color of absorbed light includes the band gap energy, but also all colors of higher energy (shorter wavelength), because electrons can be excited from the valence band to a range of energies in the conduction band. Thus semiconductors with band gaps in the infrared (e.g., Si, 1.1 eV and GaAs, 1.4 eV) appear black because they absorb all colors of visible light. Wide band gap semiconductors such as TiO_{2} (3.0 eV) are white because they absorb only in the UV. Fe_{2}O_{3} has a band gap of 2.2 eV and thus absorbs light with λ < 560 nm. It thus appears reddishorange (the colors of light reflected from Fe_{2}O_{3}) because it absorbs green, blue, and violet light. Similarly, CdS (E_{gap} = 2.6 eV) is yellow because it absorbs blue and violet light.
Electrons and holes in semiconductors
Pure (undoped) semiconductors can conduct electricity when electrons are promoted, either by heat or light, from the valence band to the conduction band. The promotion of an electron (e^{}) leaves behind a hole (h^{+}) in the valence band. The hole, which is the absence of an electron in a bonding orbital, is also a mobile charge carrier, but with a positive charge. The motion of holes in the lattice can be pictured as analogous to the movement of an empty seat in a crowded theater. An empty seat in the middle of a row can move to the end of the row (to accommodate a person arriving late to the movie) if everyone moves over by one seat. Because the movement of the hole is in the opposite direction of electron movement, it acts as a positive charge carrier in an electric field.
The opposite process of excitation, which creates an electronhole pair, is their recombination. When a conduction band electron drops down to recombine with a valence band hole, both are annihilated and energy is released. This release of energy is responsible for the emission of light in LEDs.
An electronhole pair is created by adding heat or light energy E > E_{gap} to a semiconductor (blue arrow). The electronhole pair recombines to release energy equal to E_{gap} (red arrow). 
At equilibrium, the creation and annihilation of electronhole pairs proceed at equal rates. This dynamic equilibrium is analogous to the dissociationassociation equilibrium of H^{+} and OH^{} ions in water. We can write a mass action expression:
\(n \times p = K_{eq} = n_{i}^{2}\)
where n and p represent the number density of electrons and holes, respectively, in units of cm^{3}. The intrinsic carrier concentration, n_{i}, is equal to the number density of electrons or holes in an undoped semiconductor, where n = p = n_{i}.
Note the similarity to the equation for water autodissociation:
\([H^{+}][OH^{}] = K_{w}\)
By analogy, we will see that when we increase n (e.g., by doping), p will decrease, and viceversa, but their product will remain constant at a given temperature.
Temperature dependence of the carrier concentration. Using the equations \(K_{eq} = e^{(\frac{ \Delta G^{o}}{RT})} \) and \(\Delta G^{o} = \Delta H^{o}  T \Delta S^{o}\), we can write:
\[ n \times p = n_{i}^{2} = e^{(\frac{\Delta S^{o}} {R})} e^{(\frac{ \Delta H^{o}}{RT})}\]
The entropy change for creating electron hole pairs is given by:
\[\Delta S^{o} = R ln (N_{V}) + R ln (N_{V}) = R ln (N_{C}N_{V})\]
where N_{V} and N_{C} are the effective density of states in the valence and conduction bands, respectively.
and thus we obtain
\[n_{i}^{2} = N_{C}N_{V} e^{({ \Delta H^{o}}{RT})}\]
Since the volume change is negligible, \(\Delta H^{o} \approx \Delta E^{o}\), and therefore \(\frac {\Delta H^{o}}{R} \approx \frac{E_{gap}}{k}\), from which we obtain
\[n_{i}^{2} = N_{C}N_{V} e^{(\frac{E_{gap}}{kT})}\]
and finally
\[\mathbf{n= p = n_{i} = (N_{C}N_{V})^{\frac{1}{2}} e^{(\frac{E_{gap}}{2kT})}}\]
For pure Si (E_{gap} = 1.1 eV) with N ≈ 10^{22}/cm^{3}, we can calculate from this equation a carrier density n_{i} of approximately 10^{10}/cm^{3} at 300 K. This is about 12 orders of magnitude lower than the valence electron density of Al, the element just to the left of Si in the periodic table. Thus we expect the conductivity of pure semiconductors to be many orders of magnitude lower than those of metals.
Conductivity of intrinsic semiconductors
The conductivity (σ) is the product of the number density of carriers (n or p), their charge (e), and their mobility (µ). Recall from Chapter 6 that µ is the ratio of the carrier drift velocity to the electric field and has units of cm^{2}/Voltsecond. Typically electrons and holes have somewhat different mobilities (µ_{e} and µ_{h}, respectively) so the conductivity is given by:
\[\sigma = ne\mu_{e} + pe\mu_{h}\]
For either type of charge carrier, we recall from Ch. 6 that the mobility μ is given by:
\[\mu = \frac{v_{drift}}{E} = \frac{e\tau}{m}\]
where e is the fundamental unit of charge, τ is the scattering time, and m is the effective mass of the charge carrier.
Taking an average of the electron and hole mobilities, and using n = p, we obtain
\[\mathbf{\sigma= \sigma_{o} e^{(\frac{E_{gap}}{2kT})}}, \: where \: \sigma_{o} = 2(N_{C}N_{V})^{\frac{1}{2}}e\mu\]
By measuring the conductivity as a function of temperature, it is possible to obtain the activation energy for conduction, which is E_{gap}/2. This kind of plot, which resembles an Arrhenius plot, is shown at the right for three different undoped semiconductors. The slope of the line in each case is E_{gap}/2k.
Plots of ln(σ) vs. inverse temperature for intrinsic semiconductors Ge (E_{gap} = 0.7 eV), Si (1.1 eV) and GaAs (1.4 eV). The slope of the line is E_{gap}/2k. 
Doping of semiconductors. Almost all applications of semiconductors involve controlled doping, which is the substitution of impurity atoms, into the lattice. Very small amounts of dopants (in the partspermillion range) dramatically affect the conductivity of semiconductors. For this reason, very pure semiconductor materials that are carefully doped  both in terms of the concentration and spatial distribution of impurity atoms  are needed.
n and ptype doping. In crystalline Si, each atom has four valence electrons and makes four bonds to its neighbors. This is exactly the right number of electrons to completely fill the valence band of the semiconductor. Introducing a phosphorus atom into the lattice (the positively charged atom in the figure at the right) adds an extra electron, because P has five valence electrons and only needs four to make bonds to its neighbors. The extra electron, at low temperature, is bound to the phosphorus atom in a hydrogenlike molecular orbital that is much larger than the 3s orbital of an isolated P atom because of the high dielectric constant of the semiconductor. In silicon, this "expanded" Bohr radius is about 42 Å, i.e., 80 times larger than in the hydrogen atom. The energy needed to ionize this electron – to allow it to move freely in the lattice  is only about 40–50 meV, which is not much larger the thermal energy (26 meV) at room temperature. Therefore the Fermi level lies just below the conduction band edge, and a large fraction of these extra electrons are promoted to the conduction band at room temperature, leaving behind fixed positive charges on the P atom sites. The crystal is ndoped, meaning that the majority carrier (electron) is negatively charged.
Alternatively, boron can be substituted for silicon in the lattice, resulting in ptype doping, in which the majority carrier (hole) is positively charged. Boron has only three valence electrons, and "borrows" one from the Si lattice, creating a positively charged hole that exists in a large hydrogenlike orbital around the B atom. This hole can become delocalized by promoting an electron from the valence band to fill the localized hole state. Again, this process requires only 40–50 meV, and so at room temperature a large fraction of the holes introduced by boron doping exist in delocalized valence band states. The Fermi level (the electron energy level that has a 50% probability of occupancy at zero temperature) lies just above the valence band edge in a ptype semiconductor.
n and ptype doping of semiconductors involves substitution of electron donor atoms (light orange) or acceptor atoms (blue) into the lattice. These substitutions introduce extra electrons or holes, respectively, which are easily ionized by thermal energy to become free carriers. The Fermi level of a doped semiconductor is a few tens of mV below the conduction band (ntype) or above the valence band (ptype). 
As noted above, the doping of semiconductors dramatically changes their conductivity. For example, the intrinsic carrier concentration in Si at 300 K is about 10^{10} cm^{3}. The mass action equilibrium for electrons and holes also applies to doped semiconductors, so we can write:
\[n \times p = n_{i}^{2} = 10^{20} cm^{6} \: at \: 300K\]
If we substitute P for Si at the level of one partpermillion, the concentration of electrons is about 10^{16} cm^{3}, since there are approximately 10^{22} Si atoms/cm^{3} in the crystal. According to the mass action equation, if n = 10^{16}, then p = 10^{4} cm^{3}. There are three consequences of this calculation:
 The density of carriers in the doped semiconductor (10^{16} cm^{3}) is much higher than in the undoped material (~10^{10} cm^{3}), so the conductivity is also many orders of magnitude higher.
 The activation energy for conduction is only 40–50 meV, so the conductivity does not change much with temperature (unlike in the intrinsic semiconductor)
 The minority carriers (in this case holes) do not contribute to the conductivity, because their concentration is so much lower than that of the majority carrier (electrons).
Similarly, for ptype materials, the conductivity is dominated by holes, and is also much higher than that of the intrinsic semiconductor.
Chemistry of semiconductor doping. Sometimes it is not immediately obvious what kind of doping (n or ptype) is induced by "messing up" a semiconductor crystal lattice. In addition to substitution of impurity atoms on normal lattice sites (the examples given above for Si), it is also possible to dope with vacancies  missing atoms  and with interstitials  extra atoms on sites that are not ordinarily occupied. Some simple rules are as follows:
 For substitutions, adding an atom to the right in the periodic table results in ntype doping, and an atom to the left in ptype doping.
For example, when TiO_{2} is doped with Nb on some of the Ti sites, or with F on O sites, the result is ntype doping. In both cases, the impurity atom has one more valence electron than the atom for which it was substituted. Similarly, substituting a small amount of Zn for Ga in GaAs, or a small amount of Li for Ni in NiO, results in ptype doping.
 Anion vacancies result in ntype doping, and cation vacancies in ptype doping.
Examples are anion vacancies in CdS_{1x} and WO_{3x}, both of which give ntype semiconductors, and copper vacancies in Cu_{1x}O, which gives a ptype semiconductor.
 Interstitial cations (e.g. Li) donate electrons to the lattice resulting in ntype doping. Interstitial anions are rather rare but would result in ptype doping.
Sometimes, there can be both p and ntype dopants in the same crystal, for example B and P impurities in a Si lattice, or cation and anion vacancies in a metal oxide lattice. In this case, the two kinds of doping compensate each other, and the doping type is determined by the one that is in higher concentration. A dopant can also be present on more than one site. For example, Si can occupy both the Ga and As sites in GaAs, and the two substitutions compensate each other. Si has a slight preference for the Ga site, however, resulting in ntype doping.