Skip to main content
Chemistry LibreTexts

Introduction to Proton NMR

This page describes what a proton NMR spectrum is and how it tells you useful things about the hydrogen atoms in organic molecules.

The background to NMR spectroscopy

Nuclear magnetic resonance is concerned with the magnetic properties of certain nuclei. On this page we are focusing on the magnetic behaviour of hydrogen nuclei - hence the term proton NMR or 1H-NMR.1H NMR spectroscopy is used more often than 13C NMR, partly because proton spectra are much easier to obtain than carbon spectra. The 13C isotope is only present in about 1% of carbon atoms, and that makes it difficult to detect. The 1H isotope is almost 99% abundant, which helps make it easier to observe. Another advantage is that 1H NMR spectroscopy gives more information than 13C NMR, as you will find out later.

Note that in this discussion, the word "proton" is used for "hydrogen atom", because it is the proton in the nucleus of the 1H isotope that is observed in these experiments. Although 2H (deuterium) and 3H (tritium) are also NMR-active, they absorb at frequencies that are different from the ones used in 1H NMR. The 1H isotope is also much more common than the other two, so 1H NMR spectroscopy is more conveniently done than 2H NMR spectroscopy.

Hydrogen atoms as little magnets

If you have a compass needle, it normally lines up with the Earth's magnetic field with the north-seeking end pointing north. Provided it isn't sealed in some sort of container, you could twist the needle around with your fingers so that it pointed south - lining it up opposed to the Earth's magnetic field. It is very unstable opposed to the Earth's field, and as soon as you let it go again, it will flip back to its more stable state.

 

 

Hydrogen nuclei also behave as little magnets and a hydrogen nucleus can also be aligned with an external magnetic field or opposed to it. Again, the alignment where it is opposed to the field is less stable (at a higher energy). It is possible to make it flip from the more stable alignment to the less stable one by supplying exactly the right amount of energy.

 

 

The energy needed to make this flip depends on the strength of the external magnetic field used, but is usually in the range of energies found in radio waves - at frequencies of about 60 - 100 MHz. (BBC Radio 4 is found between 92 - 95 MHz!)

It's possible to detect this interaction between the radio waves of just the right frequency and the proton as it flips from one orientation to the other as a peak on a graph. This flipping of the proton from one magnetic alignment to the other by the radio waves is known as the resonance condition.

The importance of the hydrogen atom's environment

What we've said so far would apply to an isolated proton, but real protons have other things around them - especially electrons. The effect of the electrons is to cut down the size of the external magnetic field felt by the hydrogen nucleus.

 

 

Suppose you were using a radio frequency of 90 MHz, and you adjusted the size of the magnetic field so that an isolated proton was in the resonance condition.

If you replaced the isolated proton with one that was attached to something, it wouldn't be feeling the full effect of the external field any more and so would stop resonating (flipping from one magnetic alignment to the other). The resonance condition depends on having exactly the right combination of external magnetic field and radio frequency.

How would you bring it back into the resonance condition again? You would have to increase the external magnetic field slightly to compensate for the effect of the electrons. Now suppose that you attached the hydrogen to something more electronegative. The electrons in the bond would be further away from the hydrogen nucleus, and so would have less effect on the magnetic field around the hydrogen.

 

 

The external magnetic field needed to bring the hydrogen into resonance will be smaller if it is attached to a more electronegative element, because the hydrogen nucleus feels more of the field. Even small differences in the electronegativities of the attached atom or groups of atoms will make a difference to the magnetic field needed to achieve resonance.

Summary

For a given radio frequency (say, 90 MHz) each hydrogen atom will need a slightly different magnetic field applied to it to bring it into the resonance condition depending on what exactly it is attached to - in other words the magnetic field needed is a useful guide to the hydrogen atom's environment in the molecule.

Features of an NMR spectrum

A simple NMR spectrum looks like this:

 

 

The peaks

There are two peaks because there are two different environments for the hydrogens - in the CH3 group and attached to the oxygen in the COOH group. They are in different places in the spectrum because they need slightly different external magnetic fields to bring them in to resonance at a particular radio frequency.

The sizes of the two peaks gives important information about the numbers of hydrogen atoms in each environment. It isn't the height of the peaks that matters, but the ratio of the areas under the peaks. If you could measure the areas under the peaks in the diagram above, you would find that they were in the ratio of 3 (for the larger peak) to 1 (for the smaller one).

That shows a ratio of 3:1 in the number of hydrogen atoms in the two environments - which is exactly what you would expect for CH3COOH.

 

The need for a standard for comparison - TMS

Before we can explain what the horizontal scale means, we need to explain the fact that it has a zero point - at the right-hand end of the scale. The zero is where you would find a peak due to the hydrogen atoms in tetramethylsilane - usually called TMS. Everything else is compared with this.

You will find that some NMR spectra show the peak due to TMS (at zero), and others leave it out. Essentially, if you have to analyse a spectrum which has a peak at zero, you can ignore it because that's the TMS peak.

TMS is chosen as the standard for several reasons. The most important are:

  • It has 12 hydrogen atoms all of which are in exactly the same environment. They are joined to exactly the same things in exactly the same way. That produces a single peak, but it's also a strong peak (because there are lots of hydrogen atoms).

  • The electrons in the C-H bonds are closer to the hydrogens in this compound than in almost any other one. That means that these hydrogen nuclei are the most shielded from the external magnetic field, and so you would have to increase the magnetic field by the greatest amount to bring the hydrogens back into resonance.

    The net effect of this is that TMS produces a peak on the spectrum at the extreme right-hand side. Almost everything else produces peaks to the left of it.

The chemical shift

The horizontal scale is shown as (ppm). is called the chemical shift and is measured in parts per million - ppm. A peak at a chemical shift of, say, 2.0 means that the hydrogen atoms which caused that peak need a magnetic field two millionths less than the field needed by TMS to produce resonance. A peak at a chemical shift of 2.0 is said to be downfield of TMS. The further to the left a peak is, the more downfield it is.

Solvents for NMR spectroscopy

NMR spectra are usually measured using solutions of the substance being investigated. It is important that the solvent itself does not contain any simple hydrogen atoms, because they would produce confusing peaks in the spectrum. There are two ways of avoiding this. You can use a solvent such as tetrachloromethane, CCl4, which does not contain any hydrogen, or you can use a solvent in which any ordinary hydrogen atoms are replaced by its isotope, deuterium - for example, CDCl3 instead of CHCl3. All the NMR spectra used on this site involve CDCl3 as the solvent.

Deuterium atoms have sufficiently different magnetic properties from ordinary hydrogen that they do not produce peaks in the area of the spectrum that we are looking at.