The 1974 Act
Up until 1974, public drinking water supplies in the United States were monitored and regulated by state and local authorities. Lists of contaminants with their various concentrations could vary from state to state. As the chemical industry grew, these same state agencies noted the presence of more and new organic chemicals in public waster systems. In order to standardize drinking water across the country, the Environmental Protection Agency (EPA) enacted the Safe Water Drinking Act of 1974.
Please put label here and this is the site for you to reference: url: https://search.creativecommons.org/search?q=drinking%20water%20and%20the%20EPA&provider&li<&searchBy
The 1974 act enabled the EPA to monitor and regulate public water systems that serve over 25 people. Implementation and enforcement of drinking water standards were still performed by each state. Regarding drinking water sources (whether surface or ground), the EPA and state agencies protect and monitor these as well. The EPA does not regulate private wells or bottled water in the United States. Well water monitoring is the responsibility of the owner. As for bottled water, the Food and Drug Administration (FDA) oversees this commodity by using EPA drinking water standards.
The first set of drinking water standards included only 22 chemicals and/or pathogens. EPA established to major types of contaminants: primary and secondary. The first of these types (Primary) of contaminants are substances (Hg, As, and U) that can be toxic in small amounts. On the other hand, secondary contaminants are less toxic species (Fe and Zn) and would include cosmetic issues (color, taste, and odor) of drinking water.
All primary contaminants have enforceable concentration values. For the majority of these pollutants , EPA lists specific limits by using the term Maximum Contaminant Level (MCL). If a water supplier exceeds a given MCL for a toxin, then fines and penalties could by imposed by the EPA. A few pathogenic impurities (Giardia Lamblia and Legionella) use Treatment Technique (TT) notation rather than numeric MCL concentrations. Water that contains an amount of these pathogens must be sanitized immediately with a standardized EPA procedure.
I need a table label here. I took the information from the EPA primary standard's website.
|MCL or TT1(mg/L)||Potential Health Effects from Long-Term Exposure Above the MCL (unless specified as short-term)||Sources of Contaminant in Drinking Water|
|Giardia lamblia||Microorganism||zero||TT3||Gastrointestinal illness (such as diarrhea, vomiting, and cramps)||Human and animal fecal waste|
|Thallium||Inorganic||0.0005||0.002||Hair loss; changes in blood; kidney, intestine, or liver problems||Leaching from ore-processing sites; discharge from electronics, glass, and drug factories|
In the table shown above, a Maximum Contaminant Level Goal (MCLG) column is displayed for each of the two drinking water impurties. MCLG values are not enforced by the EPA. Instead, MCLG are suggested values that water suppliers should strive to meet. Every six years, the EPA reviews each primary contaminant with its MCL standard. During these times, they analyze data in regards to health risk assessment. If they choose to lower a MCL (smaller value) of a contaminant, then less health issues should occur. Unfortunately, reducing a concentration requires more technology which will cost the supplier and the consumer more money. By providing MCLG limits, the EPA encourages a water company to gradually work towards lowering a toxin's concentration.
Primary Drinking Water Contaminants
These types of toxins are classified into one of the six EPA classifications: microorganisms, disinfectants, disinfectant byproducts, inorganics, organics, or radionuclides. Primary contaminants are regulated because the have the capacity to do great harm to humans, plants, and animals. If a water distributor (must serve at least 200 homes) exceeds one of these mandated standards, then the EPA may impose a fine on the company.
This picture needs a label and it is having a bad day... needs to be upright. I can type the description. I took this picture.
Typically, concentrations of these contaminants are listed in parts per million. Metric amounts of a part per million are milligrams of the toxin per liter of water.
Equation showing ppm = mg/L (make mg vertical over liter) Can you make an equation for this and center it?
EPA MCL image to be inserted here (include dioxin.
For extremely toxic substance, it is more practical to use ppb units (or micrograms of contaminant per liter of water). mention differences between mcl and mclg. weird radionuclide units and asbestos......
Amendment SDWA of 1986
Amendment of SDWA of 1996