Skip to main content
Chemistry LibreTexts

13.1: Vernier LabQuest 3 Instructions

  • Page ID
    548039
  • ​

    ​

    \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \)

    \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)

    \( \newcommand{\dsum}{\displaystyle\sum\limits} \)

    \( \newcommand{\dint}{\displaystyle\int\limits} \)

    \( \newcommand{\dlim}{\displaystyle\lim\limits} \)

    \( \newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\)

    ( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\)

    \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\)

    \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\)

    \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\)

    \( \newcommand{\Span}{\mathrm{span}}\)

    \( \newcommand{\id}{\mathrm{id}}\)

    \( \newcommand{\Span}{\mathrm{span}}\)

    \( \newcommand{\kernel}{\mathrm{null}\,}\)

    \( \newcommand{\range}{\mathrm{range}\,}\)

    \( \newcommand{\RealPart}{\mathrm{Re}}\)

    \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\)

    \( \newcommand{\Argument}{\mathrm{Arg}}\)

    \( \newcommand{\norm}[1]{\| #1 \|}\)

    \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\)

    \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\AA}{\unicode[.8,0]{x212B}}\)

    \( \newcommand{\vectorA}[1]{\vec{#1}}      % arrow\)

    \( \newcommand{\vectorAt}[1]{\vec{\text{#1}}}      % arrow\)

    \( \newcommand{\vectorB}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \)

    \( \newcommand{\vectorC}[1]{\textbf{#1}} \)

    \( \newcommand{\vectorD}[1]{\overrightarrow{#1}} \)

    \( \newcommand{\vectorDt}[1]{\overrightarrow{\text{#1}}} \)

    \( \newcommand{\vectE}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash{\mathbf {#1}}}} \)

    \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \)

    \(\newcommand{\longvect}{\overrightarrow}\)

    \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)

    \(\newcommand{\ket}[1]{\left| #1 \right>}\)
    \(\newcommand{\bra}[1]{\left< #1 \right|}\)
    \(\newcommand{\braket}[2]{\left< #1 \vphantom{#2} \right| \left. #2 \vphantom{#1} \right>}\)
    \(\newcommand{\braopket}[3]{\left< #1 \vphantom{#2}\vphantom{#3} \right| #2 \vphantom{#1}\vphantom{#3} \left| #3 \vphantom{#1}\vphantom{#2} \right>}\)
    \(\newcommand{\qmvec}[1]{\mathbf{\vec{#1}}}\)
    \(\newcommand{\op}[1]{\hat{\mathbf{#1}}}\)
    \(\newcommand{\expect}[1]{\langle #1 \rangle}\)
    \(\newcommand{\dfn}[1]{\emph{\textbf{#1}}}\)

    \(\newcommand{\avec}{\mathbf a}\) \(\newcommand{\bvec}{\mathbf b}\) \(\newcommand{\cvec}{\mathbf c}\) \(\newcommand{\dvec}{\mathbf d}\) \(\newcommand{\dtil}{\widetilde{\mathbf d}}\) \(\newcommand{\evec}{\mathbf e}\) \(\newcommand{\fvec}{\mathbf f}\) \(\newcommand{\nvec}{\mathbf n}\) \(\newcommand{\pvec}{\mathbf p}\) \(\newcommand{\qvec}{\mathbf q}\) \(\newcommand{\svec}{\mathbf s}\) \(\newcommand{\tvec}{\mathbf t}\) \(\newcommand{\uvec}{\mathbf u}\) \(\newcommand{\vvec}{\mathbf v}\) \(\newcommand{\wvec}{\mathbf w}\) \(\newcommand{\xvec}{\mathbf x}\) \(\newcommand{\yvec}{\mathbf y}\) \(\newcommand{\zvec}{\mathbf z}\) \(\newcommand{\rvec}{\mathbf r}\) \(\newcommand{\mvec}{\mathbf m}\) \(\newcommand{\zerovec}{\mathbf 0}\) \(\newcommand{\onevec}{\mathbf 1}\) \(\newcommand{\real}{\mathbb R}\) \(\newcommand{\twovec}[2]{\left[\begin{array}{r}#1 \\ #2 \end{array}\right]}\) \(\newcommand{\ctwovec}[2]{\left[\begin{array}{c}#1 \\ #2 \end{array}\right]}\) \(\newcommand{\threevec}[3]{\left[\begin{array}{r}#1 \\ #2 \\ #3 \end{array}\right]}\) \(\newcommand{\cthreevec}[3]{\left[\begin{array}{c}#1 \\ #2 \\ #3 \end{array}\right]}\) \(\newcommand{\fourvec}[4]{\left[\begin{array}{r}#1 \\ #2 \\ #3 \\ #4 \end{array}\right]}\) \(\newcommand{\cfourvec}[4]{\left[\begin{array}{c}#1 \\ #2 \\ #3 \\ #4 \end{array}\right]}\) \(\newcommand{\fivevec}[5]{\left[\begin{array}{r}#1 \\ #2 \\ #3 \\ #4 \\ #5 \\ \end{array}\right]}\) \(\newcommand{\cfivevec}[5]{\left[\begin{array}{c}#1 \\ #2 \\ #3 \\ #4 \\ #5 \\ \end{array}\right]}\) \(\newcommand{\mattwo}[4]{\left[\begin{array}{rr}#1 \amp #2 \\ #3 \amp #4 \\ \end{array}\right]}\) \(\newcommand{\laspan}[1]{\text{Span}\{#1\}}\) \(\newcommand{\bcal}{\cal B}\) \(\newcommand{\ccal}{\cal C}\) \(\newcommand{\scal}{\cal S}\) \(\newcommand{\wcal}{\cal W}\) \(\newcommand{\ecal}{\cal E}\) \(\newcommand{\coords}[2]{\left\{#1\right\}_{#2}}\) \(\newcommand{\gray}[1]{\color{gray}{#1}}\) \(\newcommand{\lgray}[1]{\color{lightgray}{#1}}\) \(\newcommand{\rank}{\operatorname{rank}}\) \(\newcommand{\row}{\text{Row}}\) \(\newcommand{\col}{\text{Col}}\) \(\renewcommand{\row}{\text{Row}}\) \(\newcommand{\nul}{\text{Nul}}\) \(\newcommand{\var}{\text{Var}}\) \(\newcommand{\corr}{\text{corr}}\) \(\newcommand{\len}[1]{\left|#1\right|}\) \(\newcommand{\bbar}{\overline{\bvec}}\) \(\newcommand{\bhat}{\widehat{\bvec}}\) \(\newcommand{\bperp}{\bvec^\perp}\) \(\newcommand{\xhat}{\widehat{\xvec}}\) \(\newcommand{\vhat}{\widehat{\vvec}}\) \(\newcommand{\uhat}{\widehat{\uvec}}\) \(\newcommand{\what}{\widehat{\wvec}}\) \(\newcommand{\Sighat}{\widehat{\Sigma}}\) \(\newcommand{\lt}{<}\) \(\newcommand{\gt}{>}\) \(\newcommand{\amp}{&}\) \(\definecolor{fillinmathshade}{gray}{0.9}\)

    This appendix contains step-by-step instructions for the common tasks used in General Chemistry II. Refer to these sections whenever a lab procedure directs you to "Calibrate" or "Setup" a sensor.


    A. Temperature Probe

    Measuring Temperature

    The Stainless Steel Temperature Probe is auto-identified by the LabQuest.

    1. Plug the probe into CH 1.
    2. The screen will display the live temperature in °C.
    3. Note: You typically do not need to press "Start/Collect" to read a temperature. Just use the live meter readout.
    4. Calibration: These probes are factory-calibrated and rarely need adjustment. If the reading seems wrong (e.g., room temperature is 80°C), check that the probe is not set to °F or K in the units menu.

    B. pH Sensor

    Two-Point pH Calibration

    pH probes drift over time. For accurate \(K_a\) or titration data, you must calibrate before use.

    1. Connect the pH Sensor to CH 1.
    2. Tap the red pH box on the meter screen → Select Calibrate.
    3. Tap Calibrate Now.
    4. First Point (Acidic):
      • Rinse the probe with distilled water and place it in the pH 4.00 buffer solution.
      • Wait for the voltage reading to stabilize.
      • Enter 4.00 in the "Value 1" field.
      • Tap Keep.
    5. Second Point (Neutral):
      • Rinse the probe and place it in the pH 7.00 buffer solution.
      • Wait for the voltage to stabilize.
      • Enter 7.00 in the "Value 2" field.
      • Tap Keep.
    6. Tap OK. The probe is now calibrated.

    C. Drop Counter (Automated Titration)

    Calibrating Drops/mL

    The "Drop Counter" counts drops, but you need to know Volume (mL). Because every plastic reagent reservoir tip is slightly different, you must tell the device exactly how large your drops are.

    1. Connect the Drop Counter to DIG 1.
    2. Tap the Mode box → Select Drop Counting.
    3. Tap the red Drop Count box → Select Calibrate → Calibrate Now.
    4. The Procedure:
      • Place a clean 10-mL graduated cylinder directly under the drop tip.
      • Open the bottom valve fully to establish a steady, slow drop rate (about 1-2 drops per second).
      • Allow the drops to fall until the cylinder is nearly full (between 9 and 10 mL).
      • Close the valve completely.
    5. The Calculation:
      • Read the exact volume in the graduated cylinder (e.g., 9.45 mL).
      • Enter this value into the LabQuest.
      • Tap Keep.
    6. The device now calculates a precise "Drops/mL" ratio for your specific setup.

    D. Manual Data Entry

    "Events with Entry" Mode

    Use this mode when you want to type in one variable (like Concentration or Volume) while the sensor records the other (like Absorbance or pH).

    1. Tap the Mode box (default is usually "Time Based").
    2. Select Events with Entry from the dropdown menu.
    3. Configure the X-Axis:
      • Name: Enter the variable you will type (e.g., "Concentration").
      • Units: Enter the units (e.g., "mol/L" or "M").
    4. Tap OK.
    5. How to Collect Data:
      • Tap Start/Collect.
      • When the sensor reading stabilizes, tap Keep.
      • A keyboard will appear. Type in the value for your X-axis (e.g., "0.05") and tap OK.
      • Repeat for all samples. Tap Stop when finished.

    E. Spectrometer (SpectroVis Plus)

    Calibration & Setup

    Step 1: Calibration (Blanking)

    1. Allow the lamp to warm up for 2-3 minutes.
    2. Fill a cuvette 3/4 full with your blank solvent (usually water).
    3. Insert the cuvette so the clear sides face the arrow/light path.
    4. Tap the red Absorbance box → Calibrate.
    5. Tap Finish Calibration → OK. (The reading should be 0.000).

    Step 2: Finding \(\lambda_{\text{max}}\) (Peak Wavelength)

    1. Insert a cuvette containing your most concentrated colored solution.
    2. Tap Start/Collect. A spectrum graph will appear.
    3. Tap Stop.
    4. Tap the highest point on the curve. The wavelength (nm) and absorbance will appear on the right. Note this wavelength.

    Step 3: Setting Up for Beer's Law

    1. Tap the Meter tab (gauge icon).
    2. Tap the Mode box.
    3. Select Events with Entry (See Appendix A.5).
    4. The device will now lock onto the \(\lambda_{\text{max}}\) you found in Step 2.

    F. Linear Fit (Regression)

    Finding Slope and Intercept

    To find the best-fit line for your data (e.g., Beer's Law or Kinetics):

    1. Tap the Graph tab.
    2. Tap Analyze → Curve Fit.
    3. Select the checkbox for your data series (usually "Absorbance").
    4. From the "Fit Equation" dropdown, select Linear.
    5. The screen will display the equation form \(y = mx + b\):
      • m (Slope): The rate of change or molar absorptivity.
      • b (Intercept): The y-value at zero.
      • r (Correlation): A value close to 1.000 indicates a good fit.
    6. Tap OK to display the line on the graph.

    G. Time-Based Settings (Kinetics)

    Changing Duration & Rate

    For Kinetics or Temperature experiments, you often need to adjust how long the sensor records.

    1. Tap the Meter tab.
    2. Tap the Mode box (it usually says "Time Based").
    3. Duration: Change this to match your reaction time (e.g., change "180 s" to "600 s").
    4. Rate/Interval:
      • Rate: Samples per second (e.g., 2 samples/s).
      • Interval: Time between samples (e.g., 0.5 s/sample).
    5. Tap OK.

    H. Managing Data Runs

    Storing & Hiding Runs

    If you want to do multiple trials (e.g., Trial 1 and Trial 2) without losing your first graph:

    1. Store a Run: Tap the File Cabinet Icon (next to the "Run 1" label). The screen will clear and prepare for "Run 2." Your old data is safe.
    2. Viewing Multiple Runs:
      • Tap the Graph tab.
      • Tap the Run Number button (e.g., "Run 2").
      • Select All Runs to see them overlayed.
    3. Strike Through Data (Outliers):
      • Tap the Table tab.
      • Tap and drag to select the "bad" data cells.
      • Tap Table (menu) → Strike Through Data.
      • The graph will ignore these points, but the data remains visible with a line through it.

    I. Graph Analysis Tools

    Statistics & Tangents

    1. Statistics (Mean/Max/Min)

    1. On the Graph tab, drag across the region of interest.
    2. Tap Analyze → Statistics.
    3. Check the box for your data column.
    4. A box will appear showing the Mean (Average), Min, and Max for that selection.

    2. Tangent (Finding Slope at a Point)

    Use this for Titrations to find the steepest part of the curve (Equivalence Point).

    1. Tap Analyze → Tangent.
    2. Tap anywhere on the graph curve.
    3. A crosshair will appear. The number displayed is the Slope at that exact instant.
    4. For titrations, the Equivalence Point is where the slope is highest (maximum value).

    J. Exporting Data

    Emailing Files for Excel

    To analyze your data in Excel or Google Sheets, you must email the text file to yourself.

    1. Ensure the LabQuest is connected to WiFi (Connections icon).
    2. Tap File → Email.
    3. Option A: Text File (Recommended for Excel)
      • Tap the Text icon.
      • Enter your email address and subject.
      • Tap Send. (You can open the .txt file in Excel).
    4. Option B: Screenshot (For Lab Reports)
      • Tap the Screenshot icon (Camera).
      • Enter your email and send.

    This page titled 13.1: Vernier LabQuest 3 Instructions was last modified on Thu, 04 Dec 2025 19:36:11 GMT and is shared under a not declared license and was authored, remixed, and/or curated by Vincent Hradil and Saadia Khan.