Common Ideal Gas Difficulties
This page looks at the assumptions which are made in the Kinetic Theory about ideal gases, and takes an introductory look at the Ideal Gas Law: pV = nRT.
Kinetic Theory assumptions about ideal gases
There is no such thing as an ideal gas, of course, but many gases behave approximately as if they were ideal at ordinary working temperatures and pressures. Real gases are dealt with in more detail on another page. The assumptions are:
 Gases are made up of molecules which are in constant random motion in straight lines.
 The molecules behave as rigid spheres.
 Pressure is due to collisions between the molecules and the walls of the container.
 All collisions, both between the molecules themselves, and between the molecules and the walls of the container, are perfectly elastic. (That means that there is no loss of kinetic energy during the collision.)
 The temperature of the gas is proportional to the average kinetic energy of the molecules.
And then two absolutely key assumptions, because these are the two most important ways in which real gases differ from ideal gases:
 There are no (or entirely negligible) intermolecular forces between the gas molecules.
 The volume occupied by the molecules themselves is entirely negligible relative to the volume of the container.
The Ideal Gas Equation
The ideal gas equation is:
\[ pV = nRT \]
On the whole, this is an easy equation to remember and use. The problems lie almost entirely in the units, which should be in strict SI units
Pressure, p
Pressure is measured in Pascals, Pa  sometimes expressed as newtons per square meter, N m^{2}. These mean exactly the same thing. Be careful if you are given pressures in kPa (kilopascals). For example, 150 kPa is 150,000 Pa. You must make that conversion before you use the ideal gas equation.
Should you want to convert from other pressure measurements:
 1 atmosphere = 101,325 Pa
 1 bar = 100 kPa = 100,000 Pa
Volume, V
This is the most likely place for you to go wrong when you use this equation. That's because the SI unit of volume is the cubic metre, m^{3}  not cm^{3} or dm^{3} with 1 m^{3} = 1000 dm^{3} = 1,000,000 cm^{3}. So if you are inserting values of volume into the equation, you first have to convert them into cubic metres.
You would have to divide a volume in dm^{3} by 1000, or in cm^{3} by a million.
Similarly, if you are working out a volume using the equation, remember to covert the answer in cubic metres into dm^{3} or cm^{3} if you need to  this time by multiplying by a 1000 or a million. If you get this wrong, you are going to end up with a silly answer, out by a factor of a thousand or a million. So it is usually fairly obvious if you have done something wrong, and you can check back again.
Number of moles, n
This is easy, of course  it is just a number. You already know that you work it out by dividing the mass in grams by the mass of one mole in grams. You will most often use the ideal gas equation by first making the substitution to give:
The gas constant, R
A value for R will be given you if you need it, or you can look it up in a data source. The SI value for R is 8.31441 J K^{1} mol^{1}.
The temperature, T
The temperature has to be in Kelvin. Don't forget to add 273 if you are given a temperature in degrees Celsius.
Using the ideal gas equation
Calculations using the ideal gas equation are included in my calculations book (see the link at the very bottom of the page), and I can't repeat them here. There are, however, a couple of calculations that I haven't done in the book which give a reasonable idea of how the ideal gas equation works.
The molar volume at stp
If you have done simple calculations from equations, you have probably used the molar volume of a gas.
1 mole of any gas occupies 22.4 dm^{3} at stp (standard temperature and pressure, taken as 0°C and 1 atmosphere pressure). You may also have used a value of 24.0 dm^{3} at room temperature and pressure (taken as about 20°C and 1 atmosphere).
These figures are actually only true for an ideal gas, and we'll have a look at where they come from.
We can use the ideal gas equation to calculate the volume of 1 mole of an ideal gas at 0°C and 1 atmosphere pressure.
First, we have to get the units right.
0°C is 273 K. T = 273 K
1 atmosphere = 101325 Pa. p = 101325 Pa
We know that n = 1, because we are trying to calculate the volume of 1 mole of gas.
And, finally, R = 8.31441 J K^{1} mol^{1}.
Slotting all of this into the ideal gas equation and then rearranging it gives:
And finally, because we are interested in the volume in cubic decimetres, you have to remember to multiply this by 1000 to convert from cubic metres into cubic decimetres.
The molar volume of an ideal gas is therefore 22.4 dm^{3} at stp.
And, of course, you could redo this calculation to find the volume of 1 mole of an ideal gas at room temperature and pressure  or any other temperature and pressure.
Finding the relative formula mass of a gas from its density
This is about as tricky as it gets using the ideal gas equation.
The density of ethane is 1.264 g dm^{3} at 20°C and 1 atmosphere. Calculate the relative formula mass of ethane.
The density value means that 1 dm^{3} of ethane weighs 1.264 g.
Again, before we do anything else, get the awkward units sorted out.
A pressure of 1 atmosphere is 101325 Pa.
The volume of 1 dm^{3} has to be converted to cubic metres, by dividing by 1000. We have a volume of 0.001 m^{3}.
The temperature is 293 K.
Now put all the numbers into the form of the ideal gas equation which lets you work with masses, and rearrange it to work out the mass of 1 mole.
The mass of 1 mole of anything is simply the relative formula mass in grams.So the relative formula mass of ethane is 30.4, to 3 sig figs. Now, if you add up the relative formula mass of ethane, C_{2}H_{6} using accurate values of relative atomic masses, you get an answer of 30.07 to 4 significant figures. Which is different from our answer  so what's wrong?
There are two possibilities.

The density value I have used may not be correct. I did the sum again using a slightly different value quoted at a different temperature from another source. This time I got an answer of 30.3. So the density values may not be entirely accurate, but they are both giving much the same sort of answer.

Ethane isn't an ideal gas. Well, of course it isn't an ideal gas  there's no such thing! However, assuming that the density values are close to correct, the error is within 1% of what you would expect. So although ethane isn't exactly behaving like an ideal gas, it isn't far off.
If you need to know about real gases, now is a good time to read about them.
Contributors
Jim Clark (Chemguide.co.uk)